800.565.3317 websales@bhd.ca

Fluke 805-NLA Hand Held Vibraiton Meter

Fluke 805 Vibration Meter is the most reliable vibration screening device available for frontline mechanical troubleshooting teams that need repeatable, severity-scaled readings of overall vibration and bearing condition.

What makes the Fluke 805 the best choice?

  • A meter - not a pen - that measures overall vibration as well as specific variables like bearing condition and temperature, to provide a more complete picture.
  • A combination vibration and force sensor tip that compensates for user variance (force or angle) yielding accurate, repeatable readings.
  • A four-level severity scale and onboard processor calculate bearing condition and overall vibration using easy-to-understand textual alerts (Good, Satisfactory, Unsatisfactory, Unacceptable).
  • Sensor sensitivity can read a wide range of frequencies (10 to 1,000 Hz and 4,000 to 20,000 Hz) covering most machine and component types.
  • Straight-forward user interface that minimizes the user inputs to RPM range and equipment type.

 

Features and Benefits

  • Innovative sensor design helps minimize measurement variations caused by device angle or contact pressure
  • Consistent data quality at both low and high frequency ranges
  • Four-level scale indicates severity of problems for overall vibration and bearing condition
  • Exportable data via USB
  • Trending in Microsoft® Excel using built-in templates
  • Overall vibration measurement (10 Hz to 1,000 Hz) for acceleration, velocity and displacement units of measurement for a wide variety of machines
  • Crest Factor+ provides reliable bearing assessment using direct sensor tip measurements between 4,000 Hz and 20,000 Hz
  • Colored lighting system (green, red) and on-screen comments indicate how much pressure needs to be applied to take measurements
  • Temperature measurement with Infrared Temperature Sensor increases diagnostic capabilities
  • On-board memory holds up to 3,500 measurements
  • Audio output for listening to bearing tones directly
  • External accelerometer support for hard to reach locations
  • Flashlight for viewing measurement locations in dark areas
  • Large screen with high resolution for easy navigation and viewing

Fluke 805 Applications

  • Chillers (refrigeration)
  • Fans
  • Cooling tower drives
  • Centrifugal pumps
  • Positive displacement pumps
  • Air compressors
  • Blowers
  • Generic gearboxes (rolling element bearings)
  • Machine tools (motor, gearboxes, spindles, etc.)
Vibration Meter
Low Frequency Range (Overall Measurement) 10 Hz to 1,000 Hz
High Frequency Range (CF+ Measurement) 4,000 Hz to 20,000 Hz
Severity Levels Good, satisfactory, unsatisfactory, unacceptable
Vibration Limit 50 g peak (100 g peak-peak)
A/D Converter 16-bit
Signal To Noise Ratio 80 dB
Sampling Rate Low frequency
20,000 Hz
High frequency 80,000 Hz
Real Time Clock Backup Coin battery
Sensor
Sensitivity 100 mV g ± 10%
Measurement Range 0.01 g to 50 g
Low Frequency Range (Overall Measurement) 10 Hz to 1,000 Hz
High Frequency Range 4,000 Hz to 20,000 Hz
Resolution 0.01 g
Accuracy At 100 Hz ± 5% of measured value
Amplitude Units
Acceleration g, m/sec²
Velocity in/sec, mm/sec
Displacement mils, mm
Infrared Thermometer (Temperature Measurement)
Range -20 °C to 200 °C (-4 °F to 392 °F)
Accuracy ±2 °C (4 °F)
Focal Length Fixed, at ~3.8 cm (1.5")
External Sensor

Note: Fluke supports but does not provide external sensors

Frequency Range 10 Hz to 1,000 Hz
Bias Voltage (To Supply Power) 20 V dc to 22 V dc
Bias current (To Supply Power) Maximum 5 mA
Firmware
External Interfaces USB 2.0 (full speed) communication
Data Capacity Database on internal flash memory
Upgrade Through USB
Memory Up to 3,500 measurements
Radiated Emission
Electrostatic Discharge: Burst Standard EN 61000-4-2
Electromagnetic Interference Standard EN 61000-4-3
RE Standard CISPR 11, Class A
Environmental
Operating Temperature -20 °C to 50 °C (-4 °F to 122 °F)
Storage Temperature -30 °C to 80 °C (-22 °F to 176 °F)
Operating Humidity 10% to 95% RH
(non-condensing)
Operating/Storage Altitude Sea level to 3,048 meters (10,000 feet)
IP Rating IP54
Vibration Limit 500g peak
Drop Test 1 meter
General Specifications
Battery Type AA (2) Lithium Iron Disulfide
Battery Life 250 measurements
Size (L x W x H) 24.1 cm x 7.1 cm x 5.8 cm
(9.5 in x 2.8 in x 2.3 in)
Weight 0.40 kg (0.89 lb)
Connectors USB mini-B 7-pin, stereo audio output jack (3.5 mm Audio Plug), external sensor jack (SMB connector)
Recommended accessories
Shimpo DT-209X
hand held tachometer with data logging and LCD display
Shimpo DT-209X Hand Held Tachometer Product Image
Shimpo DT-326
60-120,000 flashes per minute handheld LED stroboscope
Shimpo DT-326 LED Stroboscope Product Image
Fluke 805 Vibration Tester PEN Product Image
call for pricing